Ourlink 750Mbps repeater is a boost range device. In this extender, You can get two signal amplifiers 2.4GHz and 5.0GHz.In 2.4 frequency your device speed is 300m & 5.0GHz its speed is 455m This repeater improves your slow wifi. In this repeater, you get a WAN and a LAN port also. you can easily connect this device with any standard router. The signal coverage of this repeater is 150m2. You are connecting this device with any LAN for assessing a new wifi connection. This repeater wifi signal link is “OURLINK_2.4g-xxxx” .when you connect this device in the WLAN setting. Its package denomination is 6.5 x 4.7 x 3.8 inches
and this repeater weighs 6.4 ounces. This device was the first time Available in the market “may 24,2018”.
How can you log in to your ourlink 750Mbps Wifi Repeater with my PC?
If you have a new repeater and you don’t know how to log in to an extender with a pc so don’t worry. Follow this prose. I hope this process is useful for you.
- Open a browser on your pc.
- In the browser URL bar write the IP address of your repeater.
- Then you will get the login page of the extender.
- On the login page, you get the username and password field. Enter both.
- The login process is complete. then go to the setup setting. Then ourlink wifi repeater setup is complete.
- If you are connecting for the first time with your repeater password you get on the back of your device “on a label”.
Why do we set up Ourlink 750Mbps repeater? How can we fix it?
Ourlink wifi repeater setup is very important if we can’t set it up with our pc or router, how it’s working, and I also have some fixing ideas how to help you to fix it.
With the WPS button- the button is a physical button, mostly you find this button on the bake on the repeater, and with this button, setup is very easy.” fix your repeater near the router and then press the WPS button of your router and after pressing and holding the WPS button of your repeater wait for some time.” I am sure with this your repeater is set with a router.
- Notes- when you press the WPS button of your device and router, so its time is only for 2min.
- Make sure reporter and router “power on”
- Setup with the ethernet cable- if you are unable to set up your device so you also set your repeater with help of an ethernet cable.
plug the ethernet cable with your device and computer in either port. Login to your device on your computer and go to settings and set up your device.
How far can your ourlink 750Mbps Repeater be from a router?
If you don’t know how far you can fix your ourlink 750Mbps dual band wifi extender, I tell you to set your repeater in between the router and your system. Like your router on the first floor and your computers are on the ground floor. So set the repeater on the steers. The extender can be 100 to 400 feet from the router.
How to reset your Repeater?
If your repeater is not working so reset your device it is used fully for your device.
“ Press and hold the reset button of your device for 30 sec.” and wait for some time. Then the reset process is complete.
Some reasons why your repeater can’t connect to the computer?
A lot of defaults are involved when you connect to a network with your extender-
Cables- If an ethernet cable is a destroyer, you are unable to connect your device. so check it or change.
Network adapters – Check the network adapter to see if it is working. Also checking whether the WiFi network is connected to the repeater or not.
Router- If your router is old, sometimes it doesn’t work so first reset your router and then connect it can type 192.168.1.250 to login.
Password- If the repeater password is incorrect then it will not connect to the PC.
Reset- If your device firmware is old then first reset it and then try connecting.
If you have an ourlink 750mbps wifi repeater, So this article will be helpful to you.
Read more – Netgear Nighthawk satellite offline